Click a question to see the answer!
How do solar cells generate electricity?
Photovoltaics or PV for short can be thought of as a direct current (DC) generator powered by the sun. When light photons of sufficient energy strike a solar cell, they knock electrons free in the silicon crystal structure forcing them through an external circuit (battery or direct DC load), and then returning them to the other side of the solar cell to start the process all over again.
The voltage output from a single crystalline solar cell is about 0.5V with an amperage output that is directly proportional to cell’s surface area (approximately 7A for a 6 inch square multicrystalline solar cell). Typically 30-36 cells are wired in series (+ to -) in each solar module. This produces a solar module with a 12V nominal output (~17V at peak power) that can then be wired in series and/or parallel with other solar modules to form a complete solar array to charge a 12, 24 or 48 volt battery bank.
Solar Systems Philippines (SSP) also offers pre-assembled Grid-Tie kits. Our popular system’s have been installed by several of our customers with a great deal of success. This kit comes with all of the equipment you’d need, including product/installation manuals, mounting rails, and clamps for your panels.
What components do I need for a grid-tie system?
Grid-tie systems are inherently simpler than either grid-tie with battery back-up or stand-alone solar systems (Off Grid). In fact, other than safety disconnects, mounting structures and wiring a grid-tie system is just solar modules and a grid-tie inverter!
Today’s sophisticated grid-tie inverters incorporate most of the components needed to convert the direct current form the modules to alternating current, track the maximum power point of the modules to operate the system at peak efficiencies and terminate the grid connection if grid power is interrupted from the utility.
What components do I need for a grid-tie system with battery back-up or OFF-grid?
There are many components that make up a complete solar system, but the 4 main items are: solar modules, charge controller(s), batteries and inverter(s). The solar modules are physically mounted on a mount structure (see question 7) and the DC power they produce is wired through a charge controller before it goes on to the battery bank where it is stored.
The two main functions of a charge controller are to prevent the battery from being overcharged and eliminate any reverse current flow from the batteries back to the solar modules at night. The battery bank stores the energy produced by the solar array during the day for use at anytime of day or night. Batteries come in many sizes and grades. The inverter takes the DC energy stored in the battery bank and inverts it to 220 VAC @ 60HZ to run your AC appliances.
Will solar work in my location?
Solar is universal and will work virtually anywhere, however some locations are better than others. Irradiance is a measure of the sun’s power available at the surface of the earth and it averages about 1000 watts per square meter. With typical crystalline solar cell efficiencies around 14-16%, that means we can expect to generate about 140-160W per square meter of solar cells placed in full sun.
Insolation is a measure of the available energy from the sun and is expressed in terms of “full sun hours” (i.e. 4 full sun hours = 4 hours of sunlight at an irradiance level of 1000 watts per square meter). Obviously different parts of the world receive more sunlight from others, so they will have more “full sun hours” per day. The solar insolation zone map in our Residential Solar Guide will give you a general idea of the “full sun hours per day” for your location.
How can I find out the average sunlight hours I get where I live?
Your average sunlight hours are fairly consistent based on where you live. For your convenience we have a solar map of the Philippines that can also estimate the size of the solar system you need based on your information. But this solar map is for your reference only, data may change overtime.
Click here to view the System Sizing Estimator.
How much will a system cost for my 2000 square foot home?
Unfortunately there is no per square foot “average” since the cost of a system actually depends on your daily energy usage and how many full sun hours you receive per day in your area; and if you have other sources of electricity. To accurately size a system to meet your needs, we need to know how much energy you use, your costs of electricity usage, and the average peak sun hours in your area. The cost of the system will depend on the percentage of electricity you hope to gain for your energy needs.
If your home is connected to the utility grid, simply look at your monthly electric bill, then call us at (032) 260-0329 to speak to a Solarian. We’re here to help you ‘electrify a sustainable world!’